6262/9, 6262/26, Idgah Road, Ambala Cantt 133001. India.

Awaiting product image

Pressure Control Trainer

This teaching and training system provides a comprehensive experimental introduction to the fundamentals of process control using an example of pressure control. The air pressure control system is a 2nd order system. It comprises two in-line pressure vessels interconnected by a restrictor valve. An additional valve on the second tank makes air tapping possible and so can be used to simulate a disturbance variable. A pressure transducer mesaures the pressure in the second vessel. The controller used is a state-of-the-art digital industrial controller. The actuator in the loop is a pneumatically operated control valve with a standardised current signal input. The controlled variable X and the manipulating variable Y are plotted directly on an integrated 2-channel line recorder. Alternatively, the variables can be tapped as analogue signals at lab jacks on the switch cabinet. This enables external recording equipment, such as an oscilloscope or a flatbed plotter, to be connected.

SKU: bb60382fad07 Category:
Request a Quote

Pressure Control Trainer

Interlabs presents Pressure Control Trainer, listed under our Process Control Eengineering range. This product page brings together the available product information to help laboratories, educational institutions, engineering departments and procurement teams assess its relevance.

Product Overview

This teaching and training system provides a comprehensive experimental introduction to the fundamentals of process control using an example of pressure control. The air pressure control system is a 2nd order system. It comprises two in-line pressure vessels interconnected by a restrictor valve. An additional valve on the second tank makes air tapping possible and so can be used to simulate a disturbance variable. A pressure transducer mesaures the pressure in the second vessel. The controller used is a state-of-the-art digital industrial controller. The actuator in the loop is a pneumatically operated control valve with a standardised current signal input. The controlled variable X and the manipulating variable Y are plotted directly on an integrated 2-channel line recorder. Alternatively, the variables can be tapped as analogue signals at lab jacks on the switch cabinet. This enables external recording equipment, such as an oscilloscope or a flatbed plotter, to be connected.

Key Information and Features

The details below are based on the supplied product description. Please confirm the final configuration, included accessories, materials, dimensions and operating requirements with Interlabs before placing an order.

Applications and Use

Pressure Control Trainer is listed in the Process Control Eengineering category. Its intended use should be assessed against the experiments, demonstrations, training activities or operational requirements described in the product information. Contact Interlabs if you need help matching the product to a particular application.

Selection and Enquiry Guidance

When evaluating this product, share your application, required configuration, quantity and any institutional or project requirements. Interlabs can help clarify available options and confirm the product details relevant to your enquiry.

Frequently Asked Questions

What category does this product belong to?

This product is listed under Process Control Eengineering.

Where can I get confirmed specifications?

Contact Interlabs with the product name and your requirements to confirm current specifications, configuration and included components.

Can I request product or bulk enquiry support?

Yes. Share the required quantity, application and delivery location with Interlabs for enquiry assistance.

Contact Interlabs

For product details, technical clarification, configuration questions or a quotation, contact Interlabs and mention Pressure Control Trainer.

Related products

  • Placeholder
    Process Control Eengineering

    Process Control Training Plant

    This training system for process control represents a fully functional process control system. It consists of four individual systems: process module, control console, fault simulator and service module. The actual process module contains the devices and loops for liquid-level, flow rate, temperature and pressure control with all necessary equipment, tanks and vessels, pipes and delay coils, various sensors and pneumatically actuated valves. The system is laid out in a way to represent a realistic part of a plant also found in heavy industry. The control console is equipped with four digital universal industrial controllers and four three-channel chart recorders. The controllers can configured independently as required and can be operated both individually and simultaneously. They all have serial interfaces permitting parameters to be set from a PC and facilitating interfacing with a process control system. The separate console for the fault simulation unit is used to study ten different typical system faults, e.g. sensor failure or cable break. These are activated using switches. Their effect on the system behavior of the system can then be investigated. The service module provides compressed air, hot and cold water for the process module. A process communication system facilitates the central control and monitoring of the system.

  • Placeholder
    Process Control Eengineering

    Training System Speed Control

    This compact teaching / training unit offers every opportunity to learn the fundamentals of process control through experimentation on a speed control system. The experimentation set-up is mounted on a solid housing which accommodates all the electronics. A transparent protective cover permits safe observation of the experiments. A DC motor drives a shaft with a mass flywheel. The dial gauge allows the speed to be read off directly at any time. The speed is measured inductively using a speed transducer. The output signal from the transducer is sent to the software controller. The output signal from the controller influences the motor current. A generator acting as a mechanical resistance to shaft rotation can be activated by the software to study the influence of disturbance variables. The powerful state-of-the-art software is an integral part of the training system, embodying the principle of hardware/software integration (HSI). It enables the experiments to be conducted and evaluated in a user-friendly manner. The software has network capability. The link between the practice system and the PC is made via a USB port. Clearly structured and comprehensive instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.

  • Placeholder
    Process Control Eengineering

    Stirred Tank Test Stand

    This demanding test stand is used to perform experiments on a multivariable system often found in practice. In this particular example, the interacting variables temperature and level are to be controlled in a stirred tank. After the heated product leaves the stirred tank, heat is transferred to the feed by a heat exchanger. A pneumatic control valve controls the tank level via product discharge. The double-walled tank is electrically heated. The system has a closed water circuit. The test stand contains high quality instrumentation. The controllers have a Profibus DP interface which allows the test stand to be monitored with optional process control software . This software can also be used to record the process variables and to tune controller parameters via PC.

  • Placeholder
    Process Control Eengineering

    Training System Level Control

    This compact teaching / training unit offers every opportunity to learn the fundamentals of process control through experimentation on a level control system. The experimentation set-up is mounted in a solid housing which also accommodates all the electronics. The transparent process tank is fed from the storage tank with the aid of a speed-controlled pump. The liquid level is measured using a pressure transducer. The transducer output signal is sent to the software controller. The controller’s output signal influences the speed of the pump motor and therefore delivery flow rate. To investigate the influence of disturbance variables, an electromagnetic proportional valve in the tank outlet can be activated by the software. The powerful state-of-the-art software is an integral part of the training system, embodying the principle of hardware/software integration (HSI). It enables the experiments to be conducted and evaluated in a user-friendly manner. The software has network capability. The link between the training system and the PC is made via a USB port. The clearly structured instructional material sets out the technological fundamentals and provides a step-by-step guide through the experiments.

Scroll to Top