Related products

• 
  Process Control Eengineering

  PH – Value Control Trainer

  This teaching and training system provides a comprehensive experimental introduction to the fundamentals of process control using an example of temperature control. A circulating pump transfers water within a closed circuit. The flow of water can be regulated by a hand-operated valve. The loop also contains a screw-in heater, a heat exchanger with fan, and three integrated thermocouples for temperature measurement. Dead times can be represented by the use of different lengths of process delay. A thyristor power controller is used as the actuator. The controller used is a state-of-the-art digital industrial controller. It can be configured as a continuous or a switching device, and can activate the heater via the actuator and / or the fan. The controlled variable X and the manipulating variable Y are plotted directly on an integrated 2-channel line recorder. Alternatively, the variables can be tapped as analogue signals at lab jacks on the switch cabinet. This enables external recording equipment, such as an oscilloscope or a flatbed plotter, to be connected. A process control software is optionally available. The software permits the construction of a complete networked system comprising multiple trainers from the series. The key process variables can also be represented, and control functions executed.

• 
  Process Control Eengineering

  Training System Temperature Control

  This compact teaching / training unit offers every opportunity to learn the fundamentals of process control through experimentation on a temperature control system. The experimentation set-up is mounted on a solid housing which accommodates all the electronics. A metal bar, which is thermally insulated with cladding, is heated or cooled at one end by a Peltier element. Three temperature transducers along the axis of the bar allow the variation in temperature along the length of the bar, and hence the associated thermal lags, to be obtained for differing operating conditions. A dial-gauge thermometer offers the advantage that the temperature can be read off directly at any time. The temperature is measured using a thermal resistor (PTC). The transducer output signal is sent to the software controller. The output signal from the controller influences the operating voltage of the Peltier element and hence the heating power. A fan that dissipates part of the heating energy can be activated by the software to investigate the influence of disturbance variables. The powerful state-of-the-art software is an integral part of the training system, embodying the principle of hardware/software integration (HSI). It enables the experiments to be conducted and evaluated in a user-friendly manner. The software has network capability. The link between the practice system and the PC is made via a USB port. The clearly structured instructional material sets out the technological fundamentals and provides a step-by-step guide through the experiments.

• 
  Process Control Eengineering

  Level Control Trainer

  This teaching and training system provides a comprehensive experimental introduction to the fundamentals of process control using an example of level control. A pump transfers water from a storage tank to the transparent process tank. The liquid level is measured by an electronic pressure transducer installed at the base of the process tank. The controller used is a state-of-the-art digital industrial controller. The actuator in the control loop is a pneumatically operated control valve with an electro-pneumatic positioner. A ball valve in the outlet line enables defined disturbance variables to be generated. The controlled variable X and the manipulating variable Y are plotted directly on an integrated 2-channel line recorder. Alternatively, the variables can be tapped as analogue signals at lab jacks on the switch cabinet. This enables external recording equipment, such as an oscilloscope or a flatbed plotter, to be connected. A process control software is optionally available. The software permits the construction of a complete networked system comprising multiple trainers from the series. The key process variables can also be represented, and control functions executed. The well-structured instructional material outlines the technological fundamentals and provides a step-by-step guide through the experiments.

• 
  Process Control Eengineering

  Temperature Control Trainer

  This teaching and training system provides a comprehensive experimental introduction to the fundamentals of process control using an example of temperature control.A circulating pump transfers water within a closed circuit. The flow of water can be regulated by a hand-operated valve. The loop also contains a screw-in heater, a heat exchanger with fan, and three integrated thermocouples for temperature measurement. Dead times can be represented by the use of different lengths of process delay. A thyristor power controller is used as the actuator. The controller used is a state-of-the-art digital industrial controller. It can be configured as a continuous or a switching device, and can activate the heater via the actuator and / or the fan. The controlled variable X and the manipulating variable Y are plotted directly on an integrated 2-channel line recorder. Alternatively, the variables can be tapped as analogue signals at lab jacks on the switch cabinet. This enables external recording equipment, such as an oscilloscope or a flatbed plotter, to be connected. A process control software is optionally available. The software permits the construction of a complete networked system comprising multiple trainers from the series. The key process variables can also be represented, and control functions executed.